WHO=1 - Lighting

Standard Command

Syntax: *WHO*WHAT*WHERE##
Examples:

*1*1*23##        Turn on light 23  
*1*0*23##        Turn off light 23  
*1*7*45##        Set dimmer 45 to 70%  
*1*18*37##       Turn on light 37 for 0.5 sec (useful for door opener etc.)  
*1*29*23##       Let light 23 blink for 5 sec (useful as a 'silent' alarm) 
*1*30*45##       Set dimmer 45 up to next level (+10%)  

WHAT Reference Standard Command (WHO=1)

Value	Description
0	OFF
0#s	Turn OFF dimmer with s seconds (0..254) dimming time to arrive at OFF A value of "0" seconds will use last used dimming time
1	ON If dimmer: ON with last percentage
1#x	Turn ON dimmer with s seconds (0..254) dimming time to arrive at last percentage of dimmer A value of "0" seconds will use last used dimming time
2	Set dimmer to 20%
3	Set dimmer to 30%
4	Set dimmer to 40%
5	Set dimmer to 50%
6	Set dimmer to 60%
7	Set dimmer to 70%
8	Set dimmer to 80%
9	Set dimmer to 90%
10	Set dimmer to 100%
11	ON for 1 min
12	ON for 2 min
13	ON for 3 min
14	ON for 4 min
15	ON for 5 min
16	ON for 15 min
17	ON for 30 sec
18	ON for 0.5 sec (useful as a push button)
20	Blinking with a frequency of 0.5 sec
21	Blinking with a frequency of 1 sec
22	Blinking with a frequency of 1.5 sec
23	Blinking with a frequency of 2 sec
24	Blinking with a frequency of 2.5 sec
25	Blinking with a frequency of 3 sec
26	Blinking with a frequency of 3.5 sec
27	Blinking with a frequency of 4 sec
28	Blinking with a frequency of 4.5 sec
29	Blinking with a frequency of 5 sec
30	Dimmer up to next 10% step
30#p#s	Dimmer p% up with s seconds (0..254) dimming time If dimmer was off before, turns on to p% Dimmer arrives max. at 100% A value of "0" seconds will use last used dimming time
31	Dimmer down to previous 10% step
31#p#s	Dimmer p% down with s seconds (0..254) dimming time Lowest percentage the dimmer arrives is 1% A value of "0" seconds will use last used dimming time
1000#	Internal Command translation, visible in monitor session only.

Parameter Commands

Syntax: *#WHO*WHERE*#PARAMETER*VALUE1[*VALUE2...]##
Examples:

*#1*43*#2*1*35*18##        Turn on light 43 for 1h:35m:18s
*#1*44#4#03*#2*0*0*13##    Turn on light 44 of interface 03 for 13s

*#1*43#4#02*#9*1##         Set max working hours to one hour

Parameter Command Reference (WHO=1)

Parameter & Values	Description
#1*p*s	Set dimmer p% up with s seconds (0..254) dimming time
#2*h*m*s	Turn ON light for a certain time Values for hours, minutes, seconds are integer
#9*h	Set max working time in hours Values for hours are integer

Status Request

Syntax: *#WHO*WHERE##

Sending a Status Request to the gateway results in a Standard Message reply.

*#1*23##      Request status of light 23   
*#1*45##      Request status of light 45 
*#1*37##      Request status of light 37  

That 45 is a dimmer, we might realize when we get another reply than 0 or 1.

WHO=0 - Scenarios

WHO Table

WHO=2 - Automation